How To Change Garage Door Code Genie

Exterior Keypad Programming

Genie Garage Door Opener Keypads

Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK

(works with remotes having ix or 12 internal code setting switches. Keypad is black with a slide-upward cover showing the Genie logo only)
This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next prepare of programming instructions below). The Door Code in the Step-Past-Footstep Process at right is determined by the internal code switches within your transmitter and the accompanying chart. Determine the settings of the first iii switches and write down the corresponding number from the chart. Proceed with the adjacent 3 switches and its corresponding number, and so on, until the concluding set of 3 switches. You should accept iii or 4 Door Code numbers.

Switch Settings			Door Lawmaking Number
Up	Up	Upwardly	vii
Upward	Up	Down	6
Upwards	Down	Up	5
Up	Down	Downwardly	iv
Down	Up	Up	3
Down	Upward	Downward	2
Down	Downwardly	Upward	1
Down	Downwardly	Downwards	0

Door Lawmaking in Footstep 4: ___ ___ ___ ___

To make a re-create, highlight area and copy into your word program. You can then print out a legible copy of the chart and the programming instructions from your give-and-take software.

Stride-By-Step Programming Procedure

1. Reset Keypad–slide keypad cover one-half fashion up. While pressing the # and viii buttons simultaneously, slide the Keypad Cover the rest of the mode upward until information technology latches. Release # and eight buttons. At this point, if the back lit keypad light stays on, proceed directly to step 2. If the back lit keypad light goes out, close the cover pad and reopen it until it clicks. Proceed to stride 2.
2. Printing iii, v, seven and # buttons in said order.
3. Enter your Pivot and press the # push button. Your PIN number can be created from any group of numbers up to eight digits of your option. Note: Exercise Not utilise"#" or "star" cardinal.
4. Enter Door Lawmaking, every bit determined from the chart above, and printing the "star" key.
5. Slide Keypad Comprehend down.
6. Test Keypad past sliding encompass up until it latches. Enter your PIN and Printing "star" key. Your door should operate.

---

Genie Wireless Intellicode Keyless Entry Pad Programming:

iii Models

Model 1: Intellicode Model GWKIC, ACSDG (black with slide-up cover and the word "Intellicode" printed on the cover)

GWKIC, ACSDG, Two Part, Step-By-Step Programming

Function ane:

To Reset the Intellicode Wireless Keypad

1. Open up cover half way.
2. Press and concur "PROG" and "8" while fully opening encompass. Indicator calorie-free will blink once and go out.
3. Close embrace fully.

To Program the Intellicode Wireless Keypad

1. Open cover fully by sliding keypad cover up until it latches.
2. Press iii-five-7.
3. Printing "PROG". (red light blinks)
4. Enter your Personal Identification Number (Pin).
5. Press "PROG". (red light blinks fast)
6. Close comprehend fully.
7. Proceed to Part 2 below.

annotation: if red indicator light does not glimmer, it is not taking the programming steps. Check the 9 volt battery nether the keypad numbers. To access, printing inward, under the number pad lip while sliding downward to expose the battery.

Office 2:

Gently press and release the Receiver Learn Code push on the Power Head Receiver of your Genie Garage Door Opener (Genie motor on the ceiling). This minor black button is located behind the lite lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the ability caput. When pressed, a radio bespeak indicator will start blinking ruddy for 30 seconds.

1. Enter your Pin number subsequently pressing the Learn Code button described above, while the motor head indicator low-cal is blinking.
2. Press "SEND" two times for your system to grab your frequency and code it in.
3. Press "Send" once to test organization and start your door moving.

Adding More Doors to Keypad:

1. Open cover fully.
2. Enter Pivot ane.
3. Press PROG, PROG, PROG.
4. Enter total number of doors (2 or iii)
5. Press PROG.
6. Follow directions below to set each door.
7. Press operator Learn Lawmaking Button.
8. Enter PIN 1.
9. Press Transport
10. Enter Door Number (1, 2 or 3)
11. Printing Send three times.
12. Shut Encompass.
13. Examination by Opening Cover, Enter PIN1, Enter i.
14. Become to next machine and follow steps 8 to thirteen.

With most Genie units, remove the light lens earth to expose the Learn Push on the motor caput. The larn push button is sometimes located on the back of the unit, or with Excelerator openers, information technology is under the light lens near the hinge of the lens globe. E'er locate the floppy antenna wire first. The Larn Button can be establish not far from this antenna. See Troubleshooting Guides for Excelerator photo.

To make a re-create, highlight surface area and re-create into your discussion program. Y'all can then print out a legible copy of the chart and programming steps from your discussion software.

---

Model two: Intellicode Model GWKP (off-white with flip-upward cover)

Programming Instructions for the GWKP Genie garage door opener keyless entry involves following the ii sets of steps below:

1. To erase the sometime Pin (personal identification number) press and hold down, in order, the "PROG," "6" and "Up/Down Arrow" keys. The red LED will blink once then turn off. Release the buttons.
2. To programme: printing, in society, but do non hold down the "3," "5," "seven" and "PROG" keys.
3. Enter your chosen PIN, anywhere from 3 to eight characters.
4. Press "PROG" (red LED blinks – twice per second and turns off)

Find the Larn Code Button and the LED indicator low-cal on your Genie motor head within the garage. It is ordinarily behind the light lens and shut to the floppy antenna wire. If your Door Opener does not take an antenna, yous have an External Receiver. The External Receiver cover must be removed to access the Learn Code push button and the indicator LED. Follow Steps 1 through iii outlined beneath:

1. Gently press and release the Learn Code button. The scarlet LED indicator calorie-free will start to glimmer. Information technology will blink for upward to 30 seconds. While it is blinking, go along to Step two:
2. Enter your PIN and printing the "Up/Down Arrow" fundamental on your keypad. The Learn Code Indicator LED will stay on.
3. Press the "Upwards/Downward Arrow" key over again. The Learn Code indicator LED turns off. Wait until the Keypad backlight turns off (approximately 30 seconds).
4. Test by entering your PIN and pressing the "Up/Down Arrow" cardinal to operate your door.

Multiple Genie Garage Door Opener Programming for GWKP- All garage doors will use the aforementioned Pivot:

1. Enter Pivot and press PROG (ruddy LED blinks once per second).
2. press PROG again (red LED blinks twice per 2d).
3. printing the number of doors y'all wish to command (ii fundamental or 3 primal).
4. printing PROG (red led blinks several times and turns off).
5. Decide which Door will be Door #1, #2, and #3.
6. Press the Acquire Code Button on the motor head.
7. Enter your PIN and press the Up/Down key on the Keypad.
8. Press the number y'all have picked for this Door Opener (key 1, 2 or iii)
9. Press the Up/Down central.
10. Echo steps 6 through 9 for each Door Opener.

To make a copy, highlight area and copy into your word plan. Y'all can then print out a legible copy of the chart and programming steps from your give-and-take software.

---

Model three:  Programming instructions for the GK-BX Wireless Intellicode Keyad.  Works with Genie systems using Intellicode 1 and Intellicode 2 controls.

Intellicode one refers to all systems made from 1995 to Present, with the exception of 2011 and 2012.  Intellicode two refers to most units made in 2011 and 2012.

Programming Intellicode 1:

Note: To articulate out factory or previous program settings press and concur both the program key and the Upwardly/Down arrow key until the light flashes twice and goes out.

1. In lodge press keys three, 5, seven
2. Printing "Program" key
3. Enter your PIN ( from 3 to viii characters)
4. Press "Program" key
5. Find the Larn Code Button and the LED indicator light on your Genie motor head inside the garage. It is ordinarily backside the lite lens and shut to the floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver. The External Receiver embrace must be removed to admission the Learn Code button and the indicator LED.
6. Open up and enter the Pivot, press the Upwardly/Downward arrow key and release several times to activate the door.

In one case your keypad is programmed, changing your present PIN can be achieved by inbound current PIN then printing Program, enter your new Pin and press Program.  The keypad should at present be set to the new PIN.

---

Programming Intellicode 3 and Intellicode 2

Intellicode three (Systems built from 2009 until July 2011)

1. Follow steps one through 5 above
2. Printing and hold the square Plan button (shown in the diagram above) located on the bottom of the motor caput, until both the round and cylinder LEDs plough BLUE.
3. Release button.  Only the round LED will be BLUE. ( note: if the round, blue LED turns off and the long, royal light starts blinking, go to instructions for Intellicode two below )
4. Printing the foursquare "Plan" button and release once more.  LEDs should glimmer Purple.
5. Use an existing remote to unlock the system by pressing information technology in one case only.
6. On the wireless keypad enter your Pivot and press the Upwardly/Downward arrow fundamental three, 4 or 5 times until door activates.
7. Wait 30 seconds until LED turns off.
8. Test by inbound Pin and pressing UP/DOWN arrow central once.

Intellicode ii  (Systems built from July 2011 to Present)

1. Follow steps one through 5 to a higher place
2. Press and hold the foursquare PROGRAM button (shown in the diagram above) located on the bottom of the motor head, until the circular LED turns Bluish and release the button.
3. Upon releasing the square push the blueish calorie-free volition turn off and the long purple button will start to blink.
4. While the majestic lite is blinking (30 seconds) get to the the keypad, enter the new code y'all programmed into the keypad and slowly press and release the Upwardly/Downwards arrow key several times until the door activates.
5. Test past entering the PIN and pressing the UP/DOWN arrow key once.

Irresolute Existing Code (Pin) to a New Lawmaking

1. Enter existing Pin (personal code) and press the Programme Primal
2. Enter new PIN and press the Plan Fundamental
3. Await for the backlight to go out on the keypad
4. Test by entering the new Pivot and pressing the Upwards/Downwards arrow key.

---

Programming Genie Hardwired Keyless Entry Pads (KEP1) (This keypad has no cover and is continued to the inside receiver by a special ribbon.)

The outside garage door keypad has a flat ribbon, which slides backside the garage door molding into the garage, and attaches to the Keyless Entry Receiver box. Behind the receiver'south cover is a switch.

Slide the switch to SET. Enter your PIN on the exterior keypad, followed by the "star" button. Slide the receiver switch back to RUN. Exam your Pin code followed by the star push.

---

Programming DOMINO Hard-Wired Keypads

1. Slide switch on box in garage to Program.
2. Press ENTER, then put in your own code ( up to vi digits) and printing ENTER once again.
3. Slide switch on box in garage to OPERATE.  Test keypad.

---

LIFTMASTER AND SEARS CRAFTSMAN WIRELESS KEYPADS

976LM, 977LM,  377LM Security Plus and 66LM Wireless Keyless Entry Systems

1. Press and release the "smart" button on garage door opener motor unit. The smart indicator calorie-free will glow steadily for thirty seconds.
2. Inside thirty seconds, enter a 4 digit personal identification number (PIN) of your choice on the keypad. And so press and hold the ENTER button.
3. Release the button when the garage door opener motor unit lights blink. It has learned the lawmaking. If lite bulbs are non installed, two clicks will be heard.

The foursquare smart push button is located on the side or the back of the motor head, and is colored crimson, green, amber, orange, or imperial. It is directly under the #i wire terminal screw.

---

PROGRAMMING THE 877MAX KEYLESS ENTRY

1. Press and concord the * and # buttons until the lights on the keypad stop blinking.
2. Enter a four digit PIN and so press the # button
3. Press the Enter button the number of times respective with your garage door opener type, shown below

# of Presses	Garage Door Opener Type
one	Security + ii.0 (Yellow Acquire Button)
2	315 MHz Security + (Regal Learn Push)
3	390 Security + (Red/Orange Learn Button)
4	390 MHz Billion Code (Dark-green Acquire Button)

4. To exit programming, press and release the "0" push button.
5. Press and release the learn push button on the garage door opener motor head in the garage.
6. Enter the four digit PIN programmed in Footstep 2 then press the Enter button until the garage door opener lights flash or but hold for iv seconds and release. Examination keypad.

---

387LM PROGRAMMING INSTRUCTIONS

For Genie or Linear openers with dip switch settings in remotes.

Record the dip switch sequence before performing steps.  For every switch in the ON or positive position tape a 1, for every switch in the OFF or negative position record a 2.  Note: PIN stands for Personal Identification Number of your selection.

Important: after step 1, perform steps 2 through 4  earlier the keypad back light goes out.

1. Press ( * ) and ( # ) keys together until keypad stops flashing.
2. Select a 4-digit PIN and enter this Pin followed by the # key.
3. Enter ID from chart beneath and press #
4. Enter the DIP switch sequence previously recorded and press #

Back light should plough off after step 4.  Test by inbound the 4 digit code or Pin and printing the zero button for enter or any key other than the # and * keys.

ID DIP Switch System

13           12 DIP switch Genie garage door openers.

14           10 DIP switch Linear garage door openers.

sixteen           10 DIP switch Stanley garage door openers.

17             9 DIP switch Genie garage door openers.

xviii             viii DIP switch Linear or Moore-O-Matic garage door openers.

Once your keypad is programmed yous can change this code in the future.  To change your pin enter your PIN and printing *, enter a new Pin and printing *

---

Source: https://www.geniedoor.com/support/programming-instructions/outside-keypad-programming/

Posted by: pintodeshe1976.blogspot.com

Share this post